How To Shut Off Water Valve To Refrigerator

How Exercise I Plough Off the Water Line to My Refrigerator?

If your fridge has an icemaker, water dispenser or both, it will have a shut off valve to aid you plough on and off water supply during repairs. This eliminates the need to plow off water supply to the entire house which tin can be very inconveniencing.

When you detect water pooling at the lesser of the refrigerator, you lot demand to instantly turn off the water supply to it by turning the close off valve clockwise. Earlier then, you will need to first locate the close off valve.

A fridge water line close off valve is located nether the kitchen skin, on the wall behind it, in the clamber space or in the basement where a 1/4-inch h2o line is continued to the cold water line. Turn the knob or the way clockwise or perpendicular to the water pipe if you take a lever.

The 1/4-inch refrigerator water supply line should ideally guide y'all to where the valve is located. This water line volition usually be made from copper or a plastic textile and is always flexible to aid you move the fridge about without putting tension on it.

If you however need to supercede the refrigerator'south water line shut off valve, you lot will have to shut off h2o to the entire business firm. Again, you will as well need to know where the master house close off valve is located.

The chief house water shut off valve is located in the basement near the water heater or in the crawl infinite, garage, or laundry room. If you lot alive in a warmer area, the shut off valve will be located on an external wall where the main h2o line enters the business firm.

This will exist on the wall facing the street. Water to the house can also be turned off from the meter shut off valve. The water meter is normally located nearly the curb or sidewalk very shut to the street inside a physical box with a plastic or metallic cover.

The following are the steps to follow to plough off h2o to your fridge's icemaker or water dispenser:

1. Locate the Close off Valve

The first thing you need to do before turning off water to the fridge is to turn off the icemaker. This will preclude it from cycling on an off and cause damage to the valve.

After turning off the icemaker, catch the refrigerator and pull information technology gently forward. The h2o supply line is connected to the fridge at the rear and this volition assist you to apace locate the valve.

If y'all are lucky, the close off valve will exist located on a wall-recessed box at the back of the fridge. The box may sometimes be covered using a plastic or metal guard. Utilise a screwdriver to remove the guard and reveal the valve.

If the valve is non backside the fridge, check how the water supply line is installed. If information technology runs through a hole in a side cabinet, information technology means the valve is found under the kitchen sink inside the chiffonier.

On the other hand, if the water supply line runs through a hole on the floor, it means the valve is located in the basement (usually at the top very close to the basement ceiling). Refrigerators water line close off valves are always located on the common cold water pipe.

What Does a Refrigerator Shut Off Valve Look Like?

At that place are several shut off valves and h2o supply lines nether the kitchen sink. You will have the usual common cold and hot water close off valves and water lines to the faucet and even more than valves if you have a dishwasher and refrigerator as well.

It is even so easy to place the fridge line shut off valve since it volition be connected to the cold h2o pipe and likewise to the copper or plastic line which also runs to the back of the refrigerator.

Most refrigerators water lines are installed on a saddle valve. A saddle valve is named as such since it looks similar a equus caballus'southward saddle and fits over the h2o pipe the mode a saddle fits over the back of a equus caballus.

Saddle valves are usually clamped on the common cold water piping nearest to the fridge. Since originally refrigerators didn't need a shut off valve, a hole is usually drilled through the floor or on a side chiffonier where the h2o line is fed through.

The good thing about installing a saddle valve is that you do not need to cut or solder the h2o pipage. The valve handle is tightened until it pieces through the water pipe.

Self-piercing saddle valves are designed to be used with copper or contumely pipes. If you lot take PEX water pipes cocky-piercing saddles valves are out of the question.

Apart from saddle valves, you lot could also have the usual compression shut off valves which have an oval knob handle. During the installation of these valves, the cold water pipe is cut then a tee is soldered on it to enable h2o to flow to the refrigerator and elsewhere in the house.

2. Plough off the H2o Supply

Once you take located the close off valve, yous volition only need to turn the handle all the clockwise to turn off water to the refrigerator. If the valve has not been operated for a long time, turning it will not be easy.

You tin can take hold of information technology with a pair of pliers and gently try to plough it. If it will still non plow easily and you suspect you might suspension information technology but go out it. Consider turning off h2o to the whole firm from the principal house shut off valve.

Note: If your refrigerator's shut off valve is in the basement, you may need a ladder to access especially if you take an unfinished basement. As I had already mentioned, the valve will exist located at the very top where the h2o pipes are.

Once in the basement, finding the shut off is easy. It will most likely exist locates directly blow the refrigerator.